1.
WATER PROOFING/DAMP PROOFING
(1.01)
INSTANT HARDNER
Highly intensified ultra rapid hardening admixture for sealing
and plugging leaks, cracks, holes, cavities and other opening
occurring in concrete walls, roofs, basement etc.
(1.02)
FERRICA FASCIA FS 201
Metal based water proofing compound most suitable for basements,
reservoirs, retaining walls, sewers, swimming pools water/fuel
tank etc.
(1.03)
WATER SEAL
A complete cementitious based permanent water proofing system
consisting of special cement, quartz, and active chemical
constituents which are capable of migrating deep into structure.
(1.04) FLEXO
Flexible slurry coating based on a special formulation of
synthetic resins, silica sand and selected cement to provide
a truly flexible yet hard wearing, water proof and protective
coating.
(1.05)
SILICON WATER REPELLENT COMPOUND
An External water proofing system for Brick-work, Cement
renderings, concrete, natural stone, asbestos sheets etc.
(1.06)
I-N-T-E-G-R-A-L WATER PROOFER (I.M.C)
("INTENSIFIED MASS CONCRETE")
A complete range of integral water proofer liquid admixture
produced specially for basic water proofing of mass and
reinforced concrete. It increases compressive strength and
bulk density of concrete.
(1.07)
COMPOUND S.B.R
It is a water resistant admixture and bonding agent for
cement system. Also used to form water and vapor resistant
bonding coasts prior to rendering or topping.
(1.08)
ELASTO-LASTIC EP-415
It is an elastomaric, liquid water proofing membrane based
on special styrene co-polymer, which forms a seamless joint
free, water and weather tight elastic membrane.
(1.09)
WATER PROOF TILE GROUT
Is an acid proof water proofing mortar for interior and
exterior fixing of ceramic walls and floors tiles and stone
wall claddings.
BITUMEN WATER PROOFING SYSTEM
(1.10)
MODIFIED BITUMEN MULTILAYER MEMBRANE
Modified bitumen reinforced water proofing membranes, most
suitable for substructure water proofing.
Available in :-
1. Non Woven Polyester Reinforcement.
2. Glass fiber Reinforcement.
(1.11) ELASTOMERIC POLYMER MODIFIED BITUMEN MEMBRANE
A Viscous, polymer modified water proofing bitumen emulsion
suitable for brush or trowel application, to water proof
and protect concrete structure above and below ground against
attack by sulphate and airborne contaminants.
(1.12)
COLD APPLIED BITUMEN EMULSION
It is a cold applied bitumen emulsion recommended for vapor/salt
barrier and damp proofing of building, facades behind granite,
marble and stone cladding, curtain walling also recommended
for protection of below grade concrete from sulphate attack.
(1.13) RUBBER LATEX BITUMEN EMULSION
A cold applied rubber latex bitumen emulsion, which form
water proofing membrane for concrete & brick foundation
retaining wall & bridge abutments to protect against
attack by chlorides and sulphates present in soil.
(1.14)
BLACK BITUMEN PAINT
A solvent carried full bodied cold applied bituminous paint
without pigment or filler for protection of concrete (Including
below ground)
iron and steel.
2.
INDUSTRIAL FLOORING/FLOOR HARDNER
(2.01) STEEL BOND FS 501
It is a scientifically advanced formulation based on metallic
aggregates, isolated & chemically compounded. Is one
of the best floor hardener capable to provide abrasion resistant
to concrete floor damaged by heavy duty utilization
(2.02)
STEEL BOND METAL TOP FS 601
The floor hardener is analytically balanced & chemically
reinforced formulation based on metallic aggregate that
procures heavy duty surface industrial floor and pavements.
(2.03)
COLOURED FLOORINGS
These are super permanent colour for cement contain pure
pigment & only are free from adulterants earth colour.
(available in six colours).
(2.04)
NON-METALLIC FLOOR HARDNER
A ready to use emery based monolithic surface hardening
compound with cement and plasticiser, which is applied as
a dry shake to the surface of wet concrete or screed.
3.
NON SHRINK GROUTS
(3.01)
STEEL GROUT
A non-shrink parable grout for industrial application, which
provide dimensional stability, impact resistance to oil
& water penetration & high strength. A non-corrosive
& non-gas forming material that can be suitable for
grouting heavy machinery equipment, anchor bolts & for
other heavy foundations.
4.
GROUTS
(4.01)
GERM PROOF GROUT
For the permanent finishing of floor & wall tiles where
germproof, chemical resistant and water proof seal is required.
(4.02) FLOGROUT
Is a tropical grade three pack solvent free epoxy resin
based grout designed for free flowing in gap widths of 10mm
to 40mm.
(4.03)
RAINBOW GROUT
Coloured powder grouting compound for use with water proof
mortar.
5.
ROOF HEAT INSULATION
(5.01)
THERMOFIX
Is a light weight foam concrete for economical, excellent
& permanent thermal insulation to maintain room temperature
& prevent head losses.
6.
BONDING AGENTS
(6.01)
S.B.R BONDING AGENT
An excellent bonding agent and multipurpose admixture, adheres
to almost every building material specially suitable for
bonding new & old concrete, tile fixing, crack repair,
screeds, renders corrosion protection of steel.
(6.02)
P.V.A BONDING COMPOUND
P.V.A Bonding compound can be used at multipurpose adhesive,
primer, sealer & admixture for cement systems. The product
will bond most common building material, concrete, brick,
timber etc, to themselves and to each or there (excepted
plastic, rubber & polythene).
(6.03)
ACRYLIC BONDING AGENT
A non re-emulsifiable Acrylic co-polymer bonding with medium
viscosity. It is used as bonding agent for application where
water proofing is needed.
(6.04)
EPOXY ADHESIVE
Is an outstanding solvent free 2 part epoxy resin specially
formulated to
provide precastconcrete manufacturers & the construction
& maintenance industries with an extremely effective
bonding/bedding repair material easy to mix and apply.
7.
JOINT SEALANTS
(7.01)
POLYSULPHIDE ELASTOMERIC TWO PARTS EXPANSION
JOINT
Available in pouring & gum grades. Recommended for high
rise building, Godown sheds, Hospital, Industrial structures
& other areas subject to thermal expansion, contraction
and movements.
(7.02)
BITUMEN IMPREGNATED, FIBER BOND JOINT FILLER
Bitumen impregnated compressible fiber board used as expansion
joint filler in concrete.
(7.03) SEAL ROD
Sell foam backing rod joint filler.
(7.04)
SEALING GUM
Is an Elastomeric sticky textured sealant possessing supper
cohesion tack & elongation properties. It is a dense
non-hardening elastic putting with excellent aging properties.
8.
CURING COMPOUND
(8.01)
CURING COMPOUND
An economical and easy to apply curing compound. Suitable
for interior scarce area & hot weather concrete suitable
emulsion for use as an aid to hydration of newly place concrete.
It does not require to be removed prior to any other surface
application such as plaster/paint etc.
9.
CONCRETE REPAIR SYSTEM
(9.01)
COMPOUND S.B.R
Styrene butadiene copolymer latex for cement system. Used
as an admixture to provide water proof and chemically resistant
mortar for the repair of the floor, beams, block masonry
crack etc.
(9.02) CRACK FILLER CF-416
Chemically modified cementetious powder to reface concrete
structure on interior & exterior for a solid compatible
finish, thermal compatibility with concrete, high compressive
strength controlled working time & resets cracking.
(9.03)
EPOXY CRACK FILLER
Two part epoxy compound for bedding & repair work on
vertical or horizontal application. Ideal for bedding bridge
beams, fixing slip bricks, securing bolts etc.
10.
ADMIXTURS
(10.1)
SUPER PLASTICIZER
Is a high performance super plasticizing concrete admixture
for the production of high quality concrete enabling precast
products to be placed faster as well as enabling demoulding
at an earlier age.
(10.2)
WATER REDUCING AGENT
A concrete admixture that reduces the amount of gauging
water required, thus increasing the strength of the concrete.
(10.3)
RETRADER
A liquid admixture for concrete and mortar which show downs
hardening in such circumstances as:
1. High ambient temperature.
2. Large pours to prevent cold joints.
3. Delay between fixing & final completion.
4. Long delivery hauls.
(10.4)
ACCELERATOR
To promote early setting of concrete without effecting the
ultimate strength. Most suitable for concrete requiring
high early strength and frost protection.
(10.5)
P.P. FIBRE
P.P Fibre are specially engineered to minimize plastic shrinkage
cracking in concrete & offers a low cost alternative
to welded wire mesh & also enhances the ductility, tensile
strength & durability of concrete.
11.
MOULD & SHUTTER RELEASE AGENT
A chemical treatment for moulds & shutter, in fact all
form works which ensures the quick clean release of concrete
castings.
